Hay Rakes


Sitrex V Rakes Model H90

Model H90-V10, High-Lift Pull Type V Rake

The H90-V10 hay rake is very simple to use and gives excellant working results. The various adjustments allow correct wheel pressure on the terrain. The oscillation of the hay rakes' main arms and of the wheel-holder small arms permit correct ground contact, even on undulating grounds. The hydraulic lift system controls the rakes lift from the tractor's cabin without any other adjustment. This permits good working performances both on quality and time required.

 

Standard Equipment:

  • Hydraulic cylinder & hoses
  • 195-65/15 tires

Sitrex V Rakes Model Q

Model Q, Compact Pull Type V Rake

The 2 wheel Q Rake gives farmers the opportunity to use a machine featuring high performance in terms of both quality and quantity, combined with great simplicity of use. The machine is compact, but designed at the same time with plenty of clearance in the area through which the raked hay goes through. This gives the machine excellent operational qualities as well as manoeuvrability and stability both while working and during transport.

The sections of the raking wheels can be folded horizontally over the carriage, since there is a special hinge tilted on two axes that enables direct switching from the working position to the transport position with no need for any manual action. This arrangement also means that the overall dimensions of the machine are limited and that it can be stabilized. The arms of the rake are secured by means of tie-rods in a safe position for transport.

Standard Equipment:

  • Adjustable pressure spring suspension
  • Ability to rake on one side only; left or right
  • Hydraulics
  • 205-75/15 tires

Options:

  • Kicker wheel kit (moves & turns unraked centre)
  • Hydraulic windrow width kit

Sitrex V Rakes Model MX - Explorer

Sitrex Model MX

High Capacity Pull Type V Rakes

The Sitrex Explorer pull-type hay rake is a medium sized V-rake. This machine is designed to obtain a maximun working width of 23'-3" and windrow widths adjustable from 3' - 5'.
The drawbar and the opening system are mounted over the wheels this allows to make a windrow without interferance with the components of the machine. All rake wheels spring-load lift independantly, this allows the machine to follow the ground contours.
Tines are made of special steel with 7mm diameter. Tines pick up the hay making fluffy windrows very suitable for baling.
A double hydraulic system, tractor driven, controls both the wheels lift and the machine total or partial opening and closing.
On the hydraulic cylinder, which controls the opening and closing of the machine, is mounted a locking valve to maintain the required working width. Even in case of hose breaking the machine remains in the same position which it has been set.

Standard Equipment:

  • 55" diameter rake wheels
  • 40 tines per wheel
  • 7mm heat-treated teeth
  • Floating rake wheels
  • Twin hydraulic cylinders
  • Numerous raking positions
  • Tapered roller bearings with seals on wheel hubs
  • 4 - 195-65x15" tires
  • Hitch jack & transport locks
  • 4" x 4" x 1/4" structural tubing
  • Operating speed: 22 km/hr

Options:

  • Hydraulic kicker wheel kit
  • Single open side kit
  • Wind guard
  • Double acting cylinder hose kit

Sitrex V Rakes Models MK10 & MK12 - Magnum

Models MK10 & MK12, High Capacity Pull Type V Rakes

The Sitrex Magnum Pull-Type Rake is the biggest model of the V-Rake Pull-Type line. Couplings of all various frame components are flexible to obtain the maximum adjustment of the machine on very rough and uneven grounds. Moreover: the drawbar and the opening system are mounted over the wheels, this allows to make a windrow without hindrances with the components of the machine. All rake wheels are spring-load lifted independently and this allows the machine to follow the ground contours. Tines are made of special steel with 7 mm 0 diameter. Tines pick up the hay making fluffy windrows very suitable for baling. A double hydraulic system, tractor driven, controls both the wheels lift and machine total or partial opening and closing. On the hydraulic cylinder, which controls the opening and closing of the machine, is mounted a locking valve to maintain the required working width. Even in case of pipe breaking the machine remains in the same position which has been set.
Our Magnum line hay rakes rake up the crop quickly and gently, enabling better drying of the hay and an excellent yield. They have rake wheels with a diameter of 55" (1.4 m), each wheel is equipped with 40 tines made of top quality spring steel. The tines are uniformly spaced and designed to collect all the product, forming a perfectly shaped swathe. The tines can be replaced individually, so as to waste as little time as possible.

The hay rakes of the Magnum range are designed in such a way that adjustments are simple to accomplish. A lever acting on a sprocket equipped with a locking mechanism enables the width of the swathe to be adjusted easily and rapidly from about 3' (0.91 m) to about 6' (1.8 m). The machine can also be equipped with an optional hydraulic device enabling adjustment of the swath directly from the tractor. Each rake wheel has its own spring enabling the correct pressure on the ground to be obtained separately, optimizing the quality and quantity of the crop. After this initial adjustment, all the subsequent adjustments are made on the whole wing of the hay rake thanks to a crank operating a shaft to which all the hay rake wheels are connected. This saves a lot of time. For transport, adjustable disk brakes stabilize each of the pivoting wheels, enabling the machine to proceed in the utmost safety with no shimmying during transport. The wide range of machines in the Magnum line covers working widths from about 21'4" (about 6.5 m) for the machines with 10 rake wheels up to about 31' (about 9.4 m) for those with 16 rake wheels.

Each rake wheel has an adjustment spring. When the spring is suitably stretched, it ensures that the pressure of the associated rake wheel against the ground is just right, for raking on any terrain. After this initial adjustment of the individual rake wheels, it is possible to make all the subsequent adjustments effective on the whole wing of the hay rake thanks to a crank, that operates a shaft, to which all the rake wheels are connected.

Standard Equipment:

  • 55" diameter rake wheels
  • 40 tines per wheel
  • 7mm heat-treated teeth
  • Floating rake wheels
  • Twin hydraulic cylinders
  • Numerous raking positions
  • Tapered roller bearings with seals on wheel hubs
  • 4 - 205-75x15" tires
  • Hitch jack & transport locks
  • 4" x 4" x 1/4" structural tubing
  • Operating speed: 22 km/hr

Options:

  • Hydraulic kicker wheel kit
  • Hydraulic rear open kit
  • Single open side kit
  • Wind guard
  • Double acting cylinder hose kit
  • Tandem walking axle

Sitrex V Rakes Models MK14, MK 16, MK18 & MK20 - Magnum

Magnum Hay Rakes

Models MK14 - MK20, High Capacity Pull Type V Rakes

The Sitrex Magnum Pull-Type Rake is the biggest model of the V-Rake Pull-Type line. Couplings of all various frame components are flexible to obtain the maximum adjustment of the machine on very rough and uneven grounds. Moreover: the drawbar and the opening system are mounted over the wheels, this allows to make a windrow without hindrances with the components of the machine. All rake wheels are spring-load lifted independently and this allows the machine to follow the ground contours. Tines are made of special steel with 7 mm 0 diameter. Tines pick up the hay making fluffy windrows very suitable for baling. A double hydraulic system, tractor driven, controls both the wheels lift and machine total or partial opening and closing. On the hydraulic cylinder, which controls the opening and closing of the machine, is mounted a locking valve to maintain the required working width. Even in case of pipe breaking the machine remains in the same position which has been set.
Our Magnum line hay rakes rake up the crop quickly and gently, enabling better drying of the hay and an excellent yield. They have rake wheels with a diameter of 55" (1.4 m), each wheel is equipped with 40 tines made of top quality spring steel. The tines are uniformly spaced and designed to collect all the product, forming a perfectly shaped swathe. The tines can be replaced individually, so as to waste as little time as possible.

The hay rakes of the Magnum range are designed in such a way that adjustments are simple to accomplish. A lever acting on a sprocket equipped with a locking mechanism enables the width of the swathe to be adjusted easily and rapidly from about 3' (0.91 m) to about 6' (1.8 m). The machine can also be equipped with an optional hydraulic device enabling adjustment of the swath directly from the tractor. Each rake wheel has its own spring enabling the correct pressure on the ground to be obtained separately, optimizing the quality and quantity of the crop. After this initial adjustment, all the subsequent adjustments are made on the whole wing of the hay rake thanks to a crank operating a shaft to which all the hay rake wheels are connected. This saves a lot of time. For transport, adjustable disk brakes stabilize each of the pivoting wheels, enabling the machine to proceed in the utmost safety with no shimmying during transport. The wide range of machines in the Magnum line covers working widths from about 21'4" (about 6.5 m) for the machines with 10 rake wheels up to about 31' (about 9.4 m) for those with 16 rake wheels.

Each rake wheel has an adjustment spring. When the spring is suitably stretched, it ensures that the pressure of the associated rake wheel against the ground is just right, for raking on any terrain. After this initial adjustment of the individual rake wheels, it is possible to make all the subsequent adjustments effective on the whole wing of the hay rake thanks to a crank, that operates a shaft, to which all the rake wheels are connected.

Standard Equipment:

  • 55" diameter rake wheels
  • 40 tines per wheel
  • 7mm heat-treated teeth
  • Floating rake wheels
  • Twin hydraulic cylinders
  • Numerous raking positions
  • Tapered roller bearings with rubber seals on wheel hubs
  • 6 - 205-75 x 15" tires
  • Hitch jack & transport locks
  • Operating speed: 22 km/hr

Options:

  • Hydraulic kicker wheel kit
  • Hydraulic rear open kit
  • Single open side kit
  • Wind guard
  • Double acting cylinder hose kit
  • Tandem walking axle

Sitrex 3 Pt Hay Rakes Model RP

Sitrex RP

Rake with very sturdy equipment. Independant and interchangeable wheels mounted on roller bearings. Left and right spreading, turning and raking action, also suitable for limited space.

The Tram/Sitrex hay rake is a premium quality product manufactured to the specifications of and exclusively for Tram Sales Ltd., by the leading hay rake manufacturer in europe. All Tram/Sitrex products are manufactured to the most exacting specifications, from the finest materials obtainable, and with the pride in workmanship which will ensure only the finest quality, longest life and trouble free service in the field.

Standard Equipment:

  • 3 point hitch
  • 55" diameter rake wheels
  • 40 tines per wheel
  • 77mm heat-treated teeth
  • Operating speed: 16 to 22 km/hr

Sitrex Pull Type Hay Rakes Model TR

Sitrex Model TR

The Sitrex TR Hay Rake is technically designed to provide fast and careful raking, while it handles hay gentler than any other ordinary parallel bar rakes. Among its main features, along with gentle handling of hay, TR is particularly suitable for rough soils and it is more useful for low crops and for wide windrows at higher speed. The nine independent spring-loaded wheels follow the contours of the ground independently one from the other and from the frame.

 

Standard Equipment:

  • Pull type
  • 55" diameter rake wheels
  • 40 tines per wheel
  • 7mm heat-treated teeth
  • 6.00x16" tires
  • Hydraulic cylinder, and hose
  • Adjustable hitch jack
Site Map | Login | Powered By: Techweavers Inc.